GE IS220PVIBH1A VIBRATION MODULE

GE IS220PVIBH1A VIBRATION MODULE Specification

Ambient Temperature Range:-30 to 65 °C
Board Compatibility:Vibration Terminal Board (TVBA)
Channels:Thirteen for Proximity and Vibration
Common Mode Voltage:Min. 5 VDC
Dimensions:3.25" high x 1.65" wide x 4.78" deep
Frame Rates:3.125, 6.25, 12.5, 25, 50, and 100 Hz
Functional Acronym/Abbreviation:PVIB
LED Indicators:4
Probe Power:-24 VDC, 12 mA load per transducer
Status LEDs:Attn, Pwr, Link, TxRx
Revisions:Rev. A, Rev. B, Rev. C, Rev. D
Model Number:IS220PVIBH1A

Demi is always online to serve you 

Sales Manager:Demi            
Email:sales8@askplc.com   

Skype: +86 18030235312     

Mob/Whatsapp/Wechat :+86 18030235312

About the GE IS220PVIBH1A VIBRATION MODULE

IS220PVIBH1A is a Vibration Monitor (PVIB) pack developed by GE under the Mark VIe control system. The Vibration Monitor (PVIB) pack connects one or two I/O Ethernet networks to the TVBA vibration terminal board electrically. The pack includes a processor board, an acquisition board, and a daughterboard, which are all common to all Mark VIe distributed I/O packs.

The pack reads vibration or proximity information from the following sensor types using channels 1 through 8: Proximitors, integrated output accelerometers (Channels 1-3 only), Velomitor, or seiseismic channels 9 through 12 only support proximitors, while channel 13 can input either a Keyphasor signal-type or a proximity-type signal.
Dual RJ45 Ethernet ports and 3-pin power input are used to power the pack. For frame rates slower than 100 Hz, the PVIB enables twin Ethernet networks. It supports frame rates of 3.125, 6.25, 12.5, 25, 50, and 100 Hz over an Ethernet network.
A DC-37 pin connector connects directly to the matching terminal board connector for output. Indicator LEDs are used to display visual diagnostics.

IS220PVIBH1A Operation Processor
The processor board is connected to an acquisition board that is appropriate to the purpose of the I/O pack or module. The soft-start circuit ramps up the voltage available on the processor board when input power is applied. The processor reset is removed, and the local power supplies are sequenced on. The CPU runs self-test procedures before loading application code from flash memory that is particular to the I/O pack or module type.

GE IS220PVIBH1A Hardware for Vibration Monitoring
The analog filter acquisition board (BAFA) and the analog processing daughterboard make up the PVIB application-specific hardware (KAPA).
Signal conditioning is provided by the analog filter acquisition board, which centers and amplifies signals to increase analog-to-digital resolution.

GE IS220PVIBH1A Firmware for Vibration Monitoring Applications
Position data from Proximitors, wideband vibration data from Proximitors, accelerometers with integrated outputs, Velomitors, and Seismics can all be used on channels 1 through 3. Position information from Proximitors, wideband vibration information from Proximitors, Velomitors, and Seismics can all be found on Channels 4 through 8. Only position information is broadcast on channels 9-12. Position feedback and Keyphasor feedback are both supported on Channel 13.

GE 3VTVZ590CD001 IS200ERBPG1ACA FEATURES

GE 3VTVZ590CD001 IS200ERBPG1ACA Control Interfaces: The backplane often includes various control interfaces such as analog inputs, digital inputs, and outputs to interface with external control systems or sensors.

GE 3VTVZ590CD001 IS200ERBPG1ACA  Communication Ports: Modern backplanes may include communication ports such as RS-485, Ethernet, or Modbus for communication with supervisory control and data acquisition (SCADA) systems or other monitoring devices.

GE 3VTVZ590CD001 IS200ERBPG1ACA Power Supply: It typically includes a power supply section to provide power to the exciter system components and possibly auxiliary systems.

GE 3VTVZ590CD001 IS200ERBPG1ACA  Monitoring and Diagnostics: Some backplanes feature built-in monitoring and diagnostic capabilities to allow operators to track the performance of the excitation system and diagnose any issues that may arise.

Our service

1. High quality
2. Timely delivery
3. We provide a large number of branded parts.
4. We have experienced employees and extensive testing facilities.
5. There is a lot of inventory.

Recommended model

Our company sells new and surplus products and develops channels to purchase such products. This site is not approved or endorsed by any of the listed manufacturers or trademarks.Our company is not an authorized distributor, dealer or representative of the products displayed on this site.All product names, trademarks, brands and logos used on this site are the property of their respective owners.The description, illustration or sale of products under these names, trademarks, brands and logos is for identification purposes only and is not intended to indicate any affiliation with or authorization by any rights holder.